Hello ,
I have Symantec Netbackup 7.0.1 that Run at Windows server 2008 R2 64
i need to Configure Catalog_Policy to send the DR files attached with the Notification Mail
so Hwo Can I do this ?
PS:: i had Enabled the Notification with Netbackup+ checked send in an Email attachment (Recommended) .
i get the mail from Netbackup with the Following body :-
Server
svnetbkup
Date
Mon May 27 14:20:59 2013
Policy
New_Catalog_Policy
Catalog Backup Status
the requested operation was successfully completed (status 0).
To ensure that the NetBackup catalog data is protected through Mon May 27 14:20:59 2013, retain a copy of the attached file, and the media or files listed below:
Catalog Recovery Media
Media Server Media ID Image File Required
* svnetbkup D895L4 New_Catalog_Policy_1369657424_FULL
* svnetbkup D895L4 New_Catalog_Policy_1369657263_FULL
DR file written to
D:\New_Catalog_Policy\New_Catalog_Policy_1369657424_FULL
* - Primary Media
Catalog Recovery Procedure for the Loss of an Entire Catalog
You should create a detailed disaster recovery plan to follow should it become necessary to restore your organization's data in the event of a disaster. A checklist of required tasks can be a tremendous tool in assisting associates in triage. For example, after the facility is safe for data to be restored, the power and data infrastructure need to be verified. When these tasks are completed, the following scenarios will help to quickly restore the NetBackup environment, and in turn, restore applications and data.
Disaster Recovery Procedure using the DR Image File
In the event of a catastrophic failure, use the following procedure to rebuild the previous NetBackup environment.
Note: If new hardware is required, make sure that the devices contain drives
capable of reading the media and that the drive controllers are capable of mounting the drives.
1. Install NetBackup.
2. Configure the devices necessary to read the media listed above.
3. Inventory the media.
4. Make sure that the master server can access the attached DR image file.
Start the NetBackup Recovery Wizard from the NetBackup Administration
Console. Or, start the wizard from a command line by entering
bprecover -wizard.
Disaster Recovery Procedure without the DR Image File
NOTE: ONLY ATTEMPT THIS AS A LAST RESORT If you do not have the attachment included with this email, use the following instructions to recover your catalog (If using OpenStorage disk pools, refer to the Shared Storage Guide to configure the disk pools instead of step 2 and 3 below ):
1. Install NetBackup.
2. Configure the devices necessary to read the media listed above.
3. Inventory the media.
4. Run:
bpimport -create_db_info [-server name] -id D895L4
5. Go to the following directory to find the DR image file
New_Catalog_Policy_1369657424_FULL:
C:\Program Files\Veritas\NetBackup\db\images\svnetbkup\1369000000\tmp
6. Delete the other files in the directory.
7. Open New_Catalog_Policy_1369657424_FULL file and find the BACKUP_ID
(for example: svnetbkup_1369657424).
8. Run:
bpimport [-server name] -backupid svnetbkup_1369657424
9. Run:
bprestore -T -w [-L progress_log] -C svnetbkup -t 35 -p New_Catalog_Policy -X -s 1369657424 -e 1369657424 /
10. Run the BAR user interface to restore the remaining image database
if the DR image is a result of an incremental backup.
11. To recover the NetBackup relational database, run:
bprecover -r -nbdb
12. Stop and Start NetBackup
13. Configure the devices if any device has changed since the last
backup.
14. To make sure the volume information is updated, inventory the media
to update the NetBackup database.